Skip to content

Cart

Your cart is empty

How To Measure Your Wall

One of the most important considerations when choosing your wallpaper is: how much do you need?

All our wallpapers are made to measure. Therefore, precise wall measurements are essential.

To produce your selected wallpaper, we require two measurements:

  • the width of the wall at its widest point

  • the height of the wall at its highest point

Depending on which type of wall you have, the way you measure it may vary. But what you want to end up with is always the same: a single rectangle, with clear measurements for width x height.

Important for all wall measurements

Measure only the area intended to be covered by the wallpaper. Do not include skirting boards, moldings, or other trim. To ensure a smooth and secure application, always add 10 cm / 4 inches per side when placing your order, regardless of wall type.

Standard wall

Measure the full width and height of the surface you wish to cover, at its widest and highest points. Exclude skirting boards and moldings.


Wall with doors or windows

If the wall includes doors, windows, or other obstacles, measure the wall as if they were not there. Any excess material will be trimmed during application.

Multiple adjoining walls

If your wallpaper is intended to flow seamlessly across multiple adjoining walls, treat the surface as one continuous surface. Combine the widths and heights (measured at the widest and highest points) of each wall and submit them as a single measurement within the same order.

Add another 5 cm / 2 inches extra for each corner.

Sloped wall

For sloped ceilings or walls, ignore the angle and measure the surface as a standard wall. Any excess material will be trimmed during application.

Staircase murals

When measuring for a staircase mural, do not follow the diagonal wall surface along the stairs. Instead, measure the full vertical distance from the highest point at the ceiling above the top of the staircase to the lowest point at floor level. Then measure the horizontal width of the staircase.

Your measurements should form a clean rectangle. Any excess material will be trimmed during application.

Still not sure? Just send us your measurements, along with a sketch or photo of your room layout, and we'll gladly help you out.

How To Prepare Your Wall

Smooth the surface

Ensure that the wall is free from loose wallpaper, flaking paint, dust, grease, or residue that could interfere with adhesion. Remove any nails, hooks, or screws, and carefully fill all holes and cracks. If the wall is uneven due to inherent texture, applying a skim coat or wallpaper primer is recommended to level the surface.

Gently sand the surface until it is completely smooth and even. If existing wallpaper has overlapping seams, trim these back to create a flat, even base.

Clean and dry the surface

Clean the wall thoroughly with a sponge using warm water mixed with a mild soap or a cleaning agent designed for paint preparation. Allow the surface to dry for at least 24 hours before continuing to hang your  wallpaper. Ensure that no areas swell when damp or contract unevenly once dry.

Before application, switch off the electricity and remove the covers from all sockets and switches.

Color the surface

If the existing wall is painted in a dark tone or features a strong pattern, we recommend repainting it in a light, neutral color. This prevents the underlying surface from showing through at panel edges and ensures a premium feeling with a clean, uniform appearance.

NOTE: Depending on the paint type, curing can take up to 4-6 weeks.

A premium wallpaper application begins long before the first panel is hung. Proper wall preparation ensures that your wallpaper is presented exactly as intended: smooth, balanced, and able to tell its full story. The level of preparation required depends on the condition of your existing walls.

Before hanging your wallpaper, the surface must be clean, flat, and completely dry. Walls that are already in excellent condition require little more than a careful, considered cleaning. Surfaces with more texture, however, demand additional attention. 

How To Hang Wallpaper

Hanging your wallpaper is a big step in bringing your personal style to life.

Checklist before hanging

  • Assemble your tools – Make sure that you have the necessary tools at hand. A complete overview can be found in our tools guide.

  • Prepare the surface – Walls should be smooth, clean, and dry before you start. See our wall preparation guide for best practices.

  • Acclimatize the wallpaper – Remove the wallpaper from its packaging, unroll it, and cut each length along the dotted marks to separate the panels. Place the wallpaper in the room where it will be installed for at least 24 hours, allowing the wallpaper to straighten and adjust to the temperature and humidity.

  • Measure your wall – Confirm that you have enough wallpaper that matches the required height and width. See our measuring guide for more detailed instructions.


Video Instructions

 



Hang your non-woven wallpaper

Unroll the wallpaper and cut along the dotted lines to separate each panel. Make sure each panel corresponds to the full height of your wall.

Pile them flat in numerical order on a clean floor surface, with panel #1 on top (see: 'Length: x' at the top right corner). Place them in the room where they will be installed for at least 24 hours to allow the material to acclimatize. 

Apply adhesive to the wall

The first panel sets the foundation for the entire installation.

Lightly mark the width of the first panel on the wall with a pencil. Using a spirit level, draw a fine vertical guideline indicating where the right edge of the panel should align.

Apply adhesive directly to the wall, covering a bit more than the full width of the panel.

Hang the first panel

When facing the wall, application starts on the left-hand side with panel #1.

NOTE: If you added safety margins when ordering, make sure to center the strip vertically on the wall. That way, the excess is evenly distributed at the top and bottom.

Align the wallpaper with your marked vertical guideline and hang the panel from the top down, gently smoothing out air bubbles as you go.

Remove any excess adhesive immediately using a clean, damp sponge or cloth.

Hang the remaining panels

Continue by aligning each new panel, in numerical order, edge-to-edge with the previous one, without overlapping. Apply adhesive to the wall for each panel, extending slightly beyond its width.

Carefully match the pattern, press the edges together firmly, and smooth out any air bubbles. Remove excess adhesive as needed.

Repeat until all panels are up.

Trim and dry

Once all panels are in place, trim excess wallpaper at the ceiling and floor using a sharp knife and straight edge.

Allow the wallpaper to dry at room temperature with good ventilation for at least 24 hours. If a radiator is mounted on the wall, keep it turned off during drying to prevent uneven shrinkage.

Feel free to share the result with us when you’re done. We love seeing how you make the room your own! 🤍

How To Hang Peel and Stick Wallpaper

Peel and Stick wallpaper is renter-friendly and removable, making it especially good if you live in an apartment or rented house.

Checklist before hanging

  • Assemble your tools – Make sure that you have the necessary tools at hand. A complete overview can be found in our tools guide.

  • Prepare the surface – Walls should be smooth, clean, and dry before you start. See our wall preparation guide for best practices.

  • Acclimatize the wallpaper – Remove the wallpaper from its packaging, unroll it, and cut each length along the dotted marks to separate the panels. Place the wallpaper in the room where it will be installed for at least 24 hours, allowing the wallpaper to straighten and adjust to the temperature and humidity.

  • Measure your wall – Confirm that you have enough wallpaper that matches the required height and width. See our measuring guide for more detailed instructions.


Hang your peel and stick wallpaper

Unroll the wallpaper and cut along the dotted lines to separate each panel. Make sure each panel corresponds to the full height of your wall.

Pile them flat in numerical order on a clean floor surface, with panel #1 on top (see: 'Length: x' at the top right corner). Place them in the room where they will be installed for at least 24 hours to allow the material to acclimatize. 



Hang the first panel

The first panel sets the foundation for the entire installation. When facing the wall, application starts on the left-hand side with panel #1.

NOTE: If your wall is sloped and the highest point is on the right, begin on the right and hang the strips in reverse order instead. Always begin at the highest point of the wall.

Lightly mark the width of the first panel on the far left of the wall with a pencil. Using a spirit level, draw a fine vertical guideline indicating where the right edge of the strip should be, and align the wallpaper with your marked vertical guideline. 

NOTE: If you added safety margins when ordering, make sure to center the strip vertically on the wall. That way, the excess is evenly distributed at the top and bottom.

Starting at the top of the wall, peel away approximately 25 cm (10 inches) of the backing paper at a time and apply the wallpaper to the wall.

Do not remove the backing all at once. Work downward gradually. Gently smooth out air bubbles as you go.


Hang the remaining panels

Continue by aligning each new panel, from left to right in numerical order, edge-to-edge with the previous one without overlapping.

Carefully match the pattern, press the edges together firmly, and smooth out any air bubbles. 

Smooth the finished wall

When all panels are installed, go over the entire wall once more using a wallpaper brush or plastic smoother. This ensures full contact between the wallpaper and the wall and enhances adhesion.



Trim and set

Once all panels are in place, trim excess wallpaper at the ceiling and floor using a sharp knife and straight edge.


Allow the wallpaper to set at room temperature for at least 24 hours. If a radiator is mounted on the wall, keep it turned off during this time to prevent uneven shrinkage.

Feel free to share the result with us when you’re done. We love seeing how you make the room your own! 🤍


When to choose Peel and Stick wallpaper

Renting: If you live in a rental and your landlord doesn’t allow traditional wallpaper, Peel and Stick is a great solution.

Temporary installations: If you only need the wallpaper for a limited time, such as for an event or in a child’s room where you want to change the design more often, Peel and Stick is a great choice.

Small spaces: For a small, simple wall or feature wall, Peel and Stick is an easy option.

When not to choose Peel and Stick wallpaper

Textured walls: If your walls are textured and you don’t plan to smooth them with wallpaper primer or skim coat first, we recommend using the paste-the-wall Premium Textured wallpaper instead.

Permanent installations: For permanent installations or commercial spaces with higher wear and tear, we recommend choosing our non-woven Premium or Premium Textured wallpaper.

Changing humidity: Peel and Stick is not suitable for rooms with significant temperature changes or fluctuating humidity, such as bathrooms.

Compare and read more in our Paper Options guide.